background image

 Equinox Trinity Beam Laser 

 

 

 

 

 

 

 

 

     Safety

What is a laser?

A laser is device that produces a special kind of light that is different from normal light sources. 

Laser light sources differ from normal light sources in that they can produce very intense beams 

of light that can remain parallel over long distances. It is this high concentration of light that can 

sometimes make lasers harmful to look directly into.

What is a Class 3B Laser?

Any device that contains a laser has to be classified depending upon the amount of laser light that 

someone might be exposed to. During design and manufacture of the product, the manufacturer 

assigns the laser product to one of the various classes defined in the Laser Product Safety 

Standard (BS/EN 60825-1:2007). The classes range from the safest, which is Class 1, through 

to the most hazardous, which is Class 4.

For example, CD and DVD players contain lasers to read the disk, and because they are normally 

inaccessible to people, they are classified as a Class 1 laser products. Laser Pointers output more 

accessible power than CD/DVD players and are normally limited to being Class 2 devices. While 

most laser lighting effects products are Class 3B and Class 4 laser products. These two classes 

have the highest potential to cause harm because they emit the greatest light output. This is, of 

course, desirable and necessary for laser lighting effects!

A laser product that emits more than 5mW of light and less than 500mW is normally classified as a 

Class 3B laser product, meaning it carries a risk of harming eyesight if viewed directly.

Are Class 3B Laser Lighting Effects safe to view?

Yes, if used responsibly, and in accordance with the relevant the guidance issued by the Health 

and Safety Executive. 

In the simplest terms, generally keeping the beams and effects above the audience will not 

present a hazard to those viewing the show or effects. When you start to aim the laser effects 

down into the audience area is when it becomes harder to tell if the effects could cause harm. 

With a Class 3B laser lighting effect, the problem can arise if the beams or effects actually hit 

someone’s face. 

If in doubt, keep the effects above the audience.

Summary of Contents for EQLA42





















Reviews: