manualshive.com logo in svg

Epson Stylus Pro 9700 Series, User Manual

Share
Download
Epson Stylus Pro 9700 Series User Manual Download Page 21

21

21

This chapter includes the following information:

•

Unpacking and assembling the Pro 7700 and Pro 9700

•

Connecting the power cord

•

Installing ink

•

Connecting to your computer and a network

•

Installing the printer software for Windows or Macintosh

•

Updating the printer firmware

•

Configuring the printer for a network

Unpacking and Assembling the Printer

Follow these steps to assemble your printer and its stand.

Before you begin, make sure you have sufficient space to set up and use the 
printer—at least 12 inches (305 mm) on all sides in addition to the 
dimensions shown:

•

53.4 × 35.6 inches (1356 × 903 mm) for the Epson Stylus Pro 7700

•

73.4 × 52 inches (1864 × 1318 mm) for the Epson Stylus Pro 9700

Chapter 1: 
Setting Up 
the Printer

WARNING: 

Four people are 

required to unpack and set 
up the printer.

Note: 

When choosing a 

place for the printer, leave 
adequate room for easy 
access and ventilation. 
Avoid locations subject to 
direct sunlight, excessive 
heat, moisture, or dust. 
Also avoid locations near 
potential sources of 
electromagnetic 
interference, such as 
loudspeakers, cordless 
phones, TVs, or air 
conditioners.

Summary of Contents for Stylus Pro 9700 Series





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands