Epson Stylus Color 300 Service Manual Download Page 27 | Manualshive

Page: 27 / 44

background image

EPSON Stylus Color 300 Service Manual

Rev. A

3-2

3.1.2 C224 MAIN Board Removal

1. Remove the upper case. (See Section 3.1.1).
2. Remove five screws (CBB/M3x6); four screws fixing the shield plate directly to the C224

MAIN Board and one screw fixing the metal bracket to the shield plate.

3. Disconnect all cables connected to the C224 MAIN Board and remove the C224 MAIN

Board.

C224 MAIN BOARD

SHIELD PLATE

Bracket

CBB (M3x6)

CBB (M3x6)

Figure 3-2. C224 MAIN Board Removal

«
...
25
26
27
28
29
...
»

Summary of Contents for Stylus Color 300













































Reviews:

No comments

Related manuals for Stylus Color 300

Brand: NCR Pages: 10

Brand: TallyGenicom Pages: 166

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

Brand: Oki Pages: 180

Brand: ABLE Systems Pages: 4

B-470-QQ Series

Brand: TEC Pages: 32

DocuPrint C3300 DX

Brand: Xerox Pages: 200

Brand: Telpar Pages: 25

Brand: Ricoh Pages: 31

Brand: E-Pos Pages: 21

Brand: FujiFilm Pages: 28

Brand: Triumph Adler Pages: 202

da Vinci 2.0 Duo

Brand: XYZ Printing Pages: 25

Brand: ZKTeco Pages: 38

Brand: Riso Pages: 266

Brand: Brother Pages: 93

Brand: Oki Pages: 159

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands