Epson GT-1200 Service Manual Download Page 52

Page: 52 / 157

GT-12000

Disassembly and Assembly

Rev. A

4-16

4.2.3.7 HP (AF) Sensor Removal

This section describes the procedure for removing the HP sensor which
detects the reference position for the AF drive mechanism (lens/CCD
sensor unit).

1. Remove the glass frame assembly. (See Section 4.2.3.5.)
2. Remove 4 screws (No.3) securing the AF drive mechanism cover which

covers the AF drive mechanism and remove the cover.

3. Rotate the screw pulley at the end of the screw shaft (a thread shaft)

manually to move the detection flag to the area where it does not
overlap with the HP sensor.

4. Release the hook fixing the HP sensor and remove it, then disconnect

the cable from the sensor.

Screws (No.3)

Cover

Figure 4-20. AF Drive Mechanism Cover Removal

Rotate this pulley manually.

HP Sensor (AF)

Detection Flag

Figure 4-21. HP Sensor (AF) Removal

Summary of Contents for GT-1200






























































































































































Search results

Summary of Contents for GT-1200

Reviews:

Related manuals for GT-1200

Brands by name

Popular brands

Epson GT-1200, Service Manual

Search results

Summary of Contents for GT-1200

Reviews:

Related manuals for GT-1200

Brands by name

Popular brands