Epson GT-1200 Service Manual Download Page 122

Page: 122 / 157

ADF

Disassembly and Assembly

Rev. A

4-9

4.2.8 Registration/Timing Sensor Removal

This section describes how to remove the registration sensor and timing
sensor in the paper feed unit.

1. Remove the paper feed unit. (See Section 4.2.4.)
2. Remove the paper guide.

The fixing screws to be removed are:

2 screws:

From each of the right and left sides of the paper
guide

2 screws:

From each of the right and left sides of the paper
guide viewed from the top. (Remove them through
the holes on the top frame of the paper guide.)

3. Lift up the paper guide to release the cable from the hooks on the

paper guide, then remove the paper guide.

4. Remove the fixing screws securing the registration sensor and the

timing sensor, and remove the sensors.

Paper Feed Unit (Viewed from the bottom)

Paper Guide

Paper Feed Unit Access Cover

Figure 4-14. Paper Guide Installation Position

Screws

Screw securing the timing sensor

Screw securing the registration sensor

Screws

Release the cable
from the hooks.

Paper Guide

Figure 4-15. Registration/Timing Sensor Removal

Summary of Contents for GT-1200






























































































































































Search results

Summary of Contents for GT-1200

Reviews:

Related manuals for GT-1200

Brands by name

Popular brands

Epson GT-1200, Service Manual

Search results

Summary of Contents for GT-1200

Reviews:

Related manuals for GT-1200

Brands by name

Popular brands