Epson EPL-N4000+ Setup Manual Download Page 66

Page: 66 / 81

Testing and Connecting the Printer

Printing a status sheet

1. Turn the power switch at the front of the printer on. The lights

and the display messages are changed in the following order:

All lights come on once and then turn off. The display shows

ROM check

The display shows

RAM check XXXMB

, with the actual

memory size of your printer, including the memory size of
optional memory modules if installed, is displayed in place
of

XXX

The display shows

SelfTest

, and then shows

Warming Up

. The

On Line

light comes on.

After about 60 seconds, the display shows

Ready

2. Press the

Enter

button. The display shows

Status Sheet

3. Press the

Enter

button again. The message on the display

starts flashing and the printer starts printing the status sheet.

4. Check the following points in the printed status sheet:

❏

The printer can print the status sheet clearly.

❏

The information on the options installed to the printer is
printed correctly. If you can find the installed option’s
name under

Hardware Configurations

title, it means

that the printer can recognize the installed option
properly.

Note:

❏

The total printer memory is the standard 64 MB plus all
installed DIMM. For example, if you install a 32 MB DIMM,
the total printer memory is 96 MB.

Summary of Contents for EPL-N4000+


















































































Search results

Summary of Contents for EPL-N4000+

Reviews:

Related manuals for EPL-N4000+

Brands by name

Popular brands

Epson EPL-N4000+, Setup Manual

Search results

Summary of Contents for EPL-N4000+

Reviews:

Related manuals for EPL-N4000+

Brands by name

Popular brands