background image

The System Summary Option

When you select the System Summary option from the Main
Menu, the SETUP program displays a summary of the
configuration settings for your system.

This is the same screen you see during system startup. You can
choose not to have the system display this screen so system
startup is faster. See page 2-8 for information on disabling this
option.

Exiting SETUP

When you leave SETUP, you can save your settings, or exit

SETUP without saving your settings. You can also return all

values to the factory defaults.

To leave SETUP, press 

E

SC

 

from any SETUP screen. From the

Main Menu, you can do the following:

Load ROM
Default Values

Loads the factory default settings

stored in ROM back into CMOS.

If you change your system
configuration and then have
problems, you can load the ROM

values to boot the system and
start over.

Load Values

from CMOS

Loads the current values stored in
CMOS for all SETUP options. This
ignores any changes you have
made using SETUP.

Save Values

Saves the changes you have made

to 

CMOS

to your configuration to CMOS.

Press 

E

SC

 

to leave SETUP and restart your computer.

2-12

Running the SETUP Program

Summary of Contents for EL 486UC+








































































































































Reviews: