Epson 2090 - LQ B/W Dot-matrix Printer User Manual Download Page 36

Page: 36 / 48

Using the Control Panel

Tear Off/Bin
(Set) button

Feeds continuous paper forward to the tear-off position.

Feeds continuous paper backward from the
tear-off position to the top-of-form position.

Selects a cut-sheet feeder bin when it is installed.

In default setting mode, selects a value.

Tear Off/Bin
lights

Both flash when continuous paper is in the tear-off
position.

Both off when continuous paper is not in the tear-off
position or when bin 1 of the optional cut-sheet feeder
is selected.

Left light is on when Card mode is selected.

Right light is on when bin 2 of the optional cut-sheet
feeder is selected.

Menu buttons

When you press the Pitch (Item

) and Tear Off/Bin (Set)

buttons at the same time, the printer enters or exits
default setting mode. See “Changing the Printer’s
Default Settings” on page 38.

Menu lights

When the printer is in default setting mode, both menu
lights are on.

Load/Eject
button

Loads a single sheet of paper.

Ejects a single sheet of paper.

Loads continuous paper from the standby position.

Feeds continuous paper backward to the standby
position if a sheet is loaded.

Micro Adjust

When you hold down the Pause button for three
seconds, the printer enters Micro Adjust mode. In this
mode, you can press the LF/FF

and Load/Eject

buttons to adjust the top-of-form or tear-off position.
See “Using the Micro Adjust Function” on page 31.

LF/FF button

Feeds paper line by line when pressed quickly.

Ejects a single sheet or advances continuous paper to
the next top-of-form position when held down.

Pause button

Stops printing temporarily, and resumes printing when
pressed again.

When held down for three seconds, enters Micro Adjust
mode. When pressed again, exits Micro Adjust mode.

Pause light

On when the printer is paused.

Flashes when the printer is in Micro Adjust mode.

Paper Out light

On when no paper is loaded in the selected paper
source or paper is not loaded correctly.

Flashes when paper has not been fully ejected or paper
is jammed.

Summary of Contents for 2090 - LQ B/W Dot-matrix Printer

















































Search results

Summary of Contents for 2090 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2090 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands

Epson 2090 - LQ B/W Dot-matrix Printer, User Manual

Search results

Summary of Contents for 2090 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2090 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands