manualshive.com logo in svg

Epsolar LS0512R, Instruction Manual, Page: 4 / 40

Share
Download
Epsolar LS0512R Instruction Manual Download Page 4

 

 

Contents

 

 

1 Important Safety Information

 .................................. 1 

2 General Information

 .................................................. 3 

2.1 Product Overview

 ........................................ 3

 

2.2 Product Features

 .......................................... 5

 

3 Installation Instructions

 ............................................ 7 

3.1 Mounting

 ....................................................... 7

 

3.2 Wiring

 .......................................................... 10

 

4 Operation

 ................................................................... 13 

4.1 Battery Charging Information

 ................. 13 

4.2 LED Indicators

 ........................................... 16 

4.3 Setting Operation

 ....................................... 18

 

5 Protections, Troubleshooting and Maintenance

 . 22 

5.1 Protection

 .................................................... 22

 

5.2 Troubleshooting

 ......................................... 23 

5.3 Maintenance

 ............................................... 25

 

6 Warranty

 .................................................................... 26 

7 Technical Specifications

 ......................................... 28 

Summary of Contents for LS0512R









































Reviews:

No comments