background image

page | 2

ATTENTION !   RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR !

CAUTION

Risk of Electrical Shock!

DO NOT OPEN!

!

 

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended 

to alert the user to the presence of uninsulated dangerous voltage within the product’s 

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to 

persons.

The exclamation point within an equilateral triangle is intended to alert the user to 

the presence of important operating and maintenance (servicing) instructions in the 

literature accompanying the appliance.

!

!

A. 

Read these instructions.

B. 

Keep these instructions.

C. 

Heed all warnings.

D. 

Follow all instructions.

E. 

Do not use this apparatus near water.

F. 

Clean only with dry cloth.

G. 

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

H. 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including 

amplifiers) that produce heat.

I. 

Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades 

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The 

wide bladed or the third prong are provided for your safety. If the provided plug does not fit into your outlet, 

consult an electrician for replacement of the obsolete outlet.

J. 

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and 

the point where they exit from the apparatus.

K. 

Only use attachments/accessories specified by the manufacturer.

L. 

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the 

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid 

injury from tip-over.

M. 

Unplug this apparatus during lightning storms or when unused for long periods of time.

N. 

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been 

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have 

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or 

has been dropped.

O. 

The equipment shall be used at maximum 45 degree C ambient temperature.

P. 

To reduce the risk of electrical shock, do not open the equipment. For safety reasons it is only allow to the 

opened by qualified service personnel.

Q.  WARNING:

 To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 

Additionally, the apparatus shall not be exposed to dripping or splashing and no objects filled with liquids 

shall be placed on the apparatus.

R. 

The mains plug is used as the disconnect device and shall remain readily operable.

S. 

The product shall be used on open bench.

T. 

No naked flame sources, such as lighted candles, should be placed on the apparatus.

U. 

The apparatus should be connected to a mains socket outlet with a protective earthing connection.

V. 

Ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, 

table-cloths, curtains, etc.

W. 

This apparatus is suitable for use in tropical climates.

Summary of Contents for EA-AMP-SUB-1D-500R













Reviews: