Episode EA-AMP-SUB-1D-500R Installation Manual Download Page 12 | Manualshive

Page: 12 / 12

background image

© 2015 Episode®

Rev: 151008-1615

WARRANTY

2-Year Limited Warranty

Episode® Amplifiers have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components

found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply

to products that have been abused, modified or disassembled. Products to be repaired under this warranty must

be returned to a designated service center with an assigned return authorization (RA) number. Contact technical

support at [email protected] for an RA number.

CONTACTING TECHNICAL SUPPORT

866.838.5052
[email protected]

«
...
10
11
12

Summary of Contents for EA-AMP-SUB-1D-500R













Reviews:

No comments

Related manuals for EA-AMP-SUB-1D-500R

Brand: Sansui Pages: 16

Brand: JEFF ROWLAND Pages: 14

Brand: Barcus-Berry Pages: 2

Brand: EBS Pages: 4

Brand: EAW Pages: 16

'65 TWIN REVERB

Brand: Fender Pages: 7

Brand: DR. Z Amplification Pages: 6

Brand: Nobsound Pages: 2

DeltaDirect for iPad

Brand: XTA Pages: 14

Brand: PKN Controls Pages: 9

Brand: Kingrex Pages: 15

Brand: Mark Pages: 16

Brand: Crown Pages: 15

Brand: Crown Pages: 1

Brand: Crown Pages: 2

Brand: Pyle Pro Pages: 5

Brand: Sony Pages: 12

XM-280GTX Marketing Specifications

Brand: Sony Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands