EPAK DS13 PRO Installation And User Manual Download Page 29

8

Glossary

ACU

Antenna Control Unit. Used to control the antenna and provide the vessel with internet
access.

Azimuth

The horizontal angle a parabolic antenna must be rotated to, in order to point to a
specific satellite in the orbit. It is defined with respect due to north for convenience.

Elevation

The vertical angle that a parabolic antenna has to set to point to a specific satellite in
the orbit. Elevation is zero when the antenna points to the horizon.

GPS

Global Positioning System

IDU

Indoor Unit

Ku-Band

The frequency range from 10.7 to 18GHz.

LNB

A  Low   Noise   Block   is   used   for   reception   (downlink)   of   satellite   signals.   It   down-
converts a block of high range frequencies to lower range. So LNBs convert Ku Band
frequencies to L Band.

NMEA

Communication standard for marine instruments

ODU

Outdoor Unit (Antenna)

Skew

Skew is the tilt of the LNB in order to align the planes of polarization of antenna & the
satellite.

UPS

Uninterrupted Power Supply. Online type is recommended for EPAK systems.

SNR

The ratio of signal power to noise power, expressed in dB. The higher the SNR, better
the signal quality.

TVRO

Maritime TV receive Only System antenna

 Doc ID 0354  15.12.20

Page 29/33

Summary of Contents for DS13 PRO


































Reviews: