EP Equipment EPL151 Operation Manual Download Page 34

Page: 34 / 52

REV. 12/2019

3.2.4 Battery type & dimensions&

Charging time

All the batteries are maintenance free.

Battery types & dimensions are as follows:

Charge the storage battery through an

external charger

•Inspect whether relevant charging

requirements are satisfied according to

“3.2.1 precautions”;

•

Park the truck securely as described 2.3.5

;

•Pull out the storage battery plug (1) and

have it connected with the charger joint

(2), so as to facilitate charging through

connecting to the charger.

RPL201/RPL201H

Tuck type battery

type

Voltage/ Rated

capacity

Dimensions

Charger

Charging time

Internal

External

WPL201

Li-ion

48V/30Ah

245×160×380

15A

RPL201/

RPL201H

Li-ion

24V/160Ah

550×190×500

50A/100A

3h/1.6h

EPL151

Li-ion

24V/55Ah

175×124×407

10A

20A

5.5h/2.5h

HPL152

Li-ion

24/20AH

193x81x300

10A

LED light mode on the charging stand

• Charging:red LED light

• Fully charged:green LED light

• Charging fault:flashing yellow LED light

• Battery fault:steady yellow LED light

NOTE

Correctly plug the battery into the charging

stand.

NOTE

HPL201

Summary of Contents for EPL151





















































Search results

Summary of Contents for EPL151

Reviews:

Related manuals for EPL151

Brands by name

Popular brands

EP Equipment EPL151, Operation Manual

Search results

Summary of Contents for EPL151

Reviews:

Related manuals for EPL151

Brands by name

Popular brands