manualshive.com logo in svg

Eoslift T12, Instructions Manual, Page: 18 / 18

Share
Download
Eoslift T12 Instructions Manual Download Page 18

30

4

． 

Brake fault

5

．

Fork arms lower automatically without operation

1

2

3

29

Trouble shooting

Brake can not be realized with control handle in the vertical and horizontal position.

Parking can not be achieved after releasing knob.

Parking can not be achieved after pressing the emergency stop button.

Check all connectors 
and wires

Yes

No

No

No

No

Yes

Yes

No

No

Yes

Yes

Yes

No

Loose

Fasten it

Check controller.

Check if 

LED lights on the 

controller 

flash

Access 
programmer

Displayed 
or not

Check if the 

key switch signal 

is normal

Fault of key 
switch

Is the flashing 

normal

According to the 
fault flashes, find 
out and eliminate 
the cause of the 
fault 

Fault of 
controller

Is the 

sensitive switch 

normal

Replace sensitive 
switch

Check if the electromagnetic brake 
is normal, replace it if necessary. 

Check the hydraulic 
hoses and connectors

Loose

Tighten it

Check for oil 
leakage

Replace the damaged 
seals with new seals

Check the 
hydraulic valve

Adjust the safety 
valve

Check solenoid 
core

Check for oil 
leakage

Replace the damaged 
seals with new seals

Check the sensitive 
switch

Oil leakage still 
occur

As it can not function 
properly, replace the 
switch.

Replace the seals 
again

T12 Series Electric  Stackers

Trouble shooting 

Summary of Contents for T12



















Reviews:

No comments