background image

4

EN

Important notes

• 

Unprofessional installation may cau-

se a fire hazard! Please read these instal-
lation instructions carefully. In particular, 
please observe the dimensions stated and 
the following notes.

• 

This device can be used by children aged 
8 upwards and by persons with physical, 
sensory, or mental disabilities, or who 
have inadequate experience and know-
ledge if they are supervised or if they have 
received adequate instruction in how to 
use the device safely and understand the 
associated risks. Children may not play 
with this device. Children may not clean 
or carry out any user maintenance if un-
supervised. 

• 

Children should be supervised to make 
sure that they will not play with the unit.

• 

 Only specialists may install and con-

nect the sauna heater, control unit and 
other electrical equipment with a fixed 
mains connection. The necessary protec-
tive measures according to VDE 0100 of § 
49 DA/6 and VDE 0100 part 703/2006-2 
must be observed.

• 

Sauna heater and controller may only be 
used in sauna cabins made of suitable, low-
resin, untreated materials (e.g. spruce).

• 

Only a sauna heater with the appropriate 
power output may be installed in the sau-
na cabin.

• 

Please provide air intake and vent ope-
nings in each sauna cabin. The air intakes 
must always be positioned behind the 
sauna heater, approx. 5 to 10 cm above 
the floor. The minimum dimensions of the 
air intake and vent openings are stated in 
the table.

• 

The duct vents are always to be positioned 
offset diagonally to the sauna heater in 
the lower area of the rear sauna wall. The 
air intake and vents may not be covered. 
Please observe the sauna cabin supplier‘s 
instructions.

• 

 

Caution: 

Covering the heater or an 

incorrectly filled stone container represent 
a fire hazard.

• 

 Inspect the sauna cabin before each 

use! In particular, ensure that no objects 
have been stored on the sauna heater or 
the IR-radiator, if applicable.  

 

Risk of fire!

• 

 

Caution:

 The high sauna heater 

temperatures generated during operation 
can cause burns.

• 

The sauna heater is not intended for in-
stallation or set-up in a niche, under a 
bench or under a sloping roof.

• 

Do not put the sauna heater into operation 
when the air intake is closed.

• 

The cabin lighting and the corresponding 
installation must correspond with the 

Summary of Contents for Filius Control



















Reviews: