EOS 94 7371 01 Installation And Operating Instructions Manual Download Page 43

Page: 43 / 56

EOS Zeus S / EOS Zeus SL - Installation and Operating Instructions

EN-43

Maintenance

6.3

Replacing the tubular heating elements

You can replace individual tubular heating elements or the entire heating
coil.

Necessary steps:



Removing the heating coil,



EN-43



Replacing the tubular heating elements,



EN-47



Inserting the heating coil,



EN-49



Replacing the entire heating coil,



EN-49

Ha tools:



Tubular heating element or heating coil



Screwdriver



Pliers



Removing the heating coil

WARNING! Ensure that the heater has been disconnected from all power
supply lines. Allow the heater to cool down.
Remove the stones from the stone grate.

Loosen the 6 screws on the decoration ring and remove it.

Summary of Contents for 94 7371 01

























































Search results

Summary of Contents for 94 7371 01

Reviews:

Related manuals for 94 7371 01

Brands by name

Popular brands

EOS 94 7371 01, Installation And Operating Instructions Manual

Search results

Summary of Contents for 94 7371 01

Reviews:

Related manuals for 94 7371 01

Brands by name

Popular brands