Enviro C60I Owner'S Manual Download Page 51

Page: 51 / 60

Secondary Installation

Figure 67: Glass Bezel with Vermiculite

Figure 68: Glass Media Bed

9. If you are using 50-3344 (Glass Media Bed) or 50-3342 (Light Kit) you may now cover the entire

media tray in a thin layer of glass pebbles; one layer is all you need.

10. You have now successfully installed your panels and media base. You may now arrange

your optional 50-3347 (Log & Rock Set); see instruction sheets for further detail.

11. Re-install the glass door and safety screen.

7. If you have media tray option 50-3343 (Glass Bezel) place the bezel strips around the tray before the

side liners are installed. If you are using 50-3344 (Glass Media Bed) or 50-3342 (Light Kit) install tray

media after the side liners.
8. Place the side liners into the side channels of the media tray. 50-3339 (Ledgestone) and 50-3340

(Enameled) will be placed in at the bottom and rotated up until seated. 50-3338 (Fluted) will be placed

in at the rear and rotated inward until seated. Once seated secure the top with the retainers using a T-20

Torx screwdriver. If using 50-3343 (Glass Bezel) pull the sides in so they butt up with the long strips.

IMPORTANT: IF THE AIR SLOT AROUND THE BURNER IS BLOCKED WITH MEDIA THIS

WILL CAUSE THE FIREPLACE NOT TO BURN PROPERLY.

AIR

AIR SLOT

Figure 69: Burner Side Cross Section

Summary of Contents for C60I





























































Search results

Summary of Contents for C60I

Reviews:

Related manuals for C60I

Brands by name

Popular brands

Enviro C60I, Owner'S Manual

Search results

Summary of Contents for C60I

Reviews:

Related manuals for C60I

Brands by name

Popular brands