Enviro C60I Owner'S Manual Download Page 50

Page: 50 / 60

Secondary Installation

Figure 65:

Panel Installation

NO MEDIA IN THIS AREA

Figure 66:

Protected Pilot Area

WARNING: Be sure there is no media in the protected pilot area of the burner

pan.

4. Wear clean vinyl gloves when handling 50-3338 (Fluted) and 50-3339 (Ledgestone) to prevent skin contact

with the refractory. Wear clean vinyl gloves when handling 50-3340 (Enameled) to prevent smudging; use

denatured alcohol to clean. Unwrap your new Enviro liner set from the protective packaging. Be careful not to

scratch or bump the liners as they are very fragile. If the liners arrive damaged please contact your nearest

Enviro dealer.

5. Remove the 3 liner retainers from inside the firebox, loosen screws using a T-20 Torx screwdriver. The

retainers are key slotted so they can be removed without removing the screws. Then remove the existing steel

liners starting with the sides first.

6. Ensure there is nothing on top of the media tray such as glass media or glass bezel strips. Angle the rear liner

into the firebox with finesse. The panel will fit in, dont worry, place one corner in towards the back and rotate

inward. Slip it into the channel behind the media tray and install the rear liner retainer.

Summary of Contents for C60I





























































Search results

Summary of Contents for C60I

Reviews:

Related manuals for C60I

Brands by name

Popular brands

Enviro C60I, Owner'S Manual

Search results

Summary of Contents for C60I

Reviews:

Related manuals for C60I

Brands by name

Popular brands