background image

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY  
THIS MANUAL IS PRINTED ON RECYCLED PAPER 

              8 2 8

 

 

 

 

  B y   S H E R W O O D   I N D U S T R I E S   L T D .  

    B   V e n t

 

O W N E R S   M A N U A L

 

Installation And Operating Instructions For Models: 

 

828 BV. FS. (Freestanding) 

 

828 BV. INS. (Insert)

 

 

 

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. 

 

WHAT TO DO IF YOU SMELL GAS 

 Open windows/Extinguish any open flame 

 Do not try to light any appliance. 

 Do not touch any electrical switch; do not use any 

phone in your building. 

 Immediately call your gas supplier from a 

neighbor's phone.    Follow the gas supplier's 
instructions. 

 If you cannot reach your gas supplier, call the fire 

department.

 

WARNING

 

If the information in this 

manual is not followed exactly, 

a fire or explosion may result 

causing property damage, 

personal injury or loss of life. 

Installation and service must 

be performed by a qualified 

installer, service agency or the 

gas supplier. 

FOR YOUR SAFETY 

Do not store or use gasoline or other Flammable vapors and liquids 

 in the vicinity of this or any other appliance.

 

Summary of Contents for 828 BV. INS.





















Reviews: