Page 6
economical. safe. simple.
HOW IT WORKS
The Envi Heater is designed with innovative “Stack Convection Technology” that eff ectively heats a room with minimal energy.
The Envi’s inner chamber simulates “stacks” of varying height, which boost airfl ow through the heater to achieve maximum
effi ciency. The end result is enhanced airfl ow at safe air temperature, all without the use of a fan. The Envi heater will provide
consistent, comfortable, silent heat without drying out the air or leaving cold spots in the room.
OVERHEAT SAFETY FEATURE
This heater is equipped with an overheat safety feature. When the heaters internal components reach a certain temperature
that could cause overheating and a possible fi re, the heater will automatically shut off . To reset the heater, unplug the heater
power cord from the electrical outlet for 10 minutes. After 10 minutes, plug the heater into the electrical outlet and turn on us-
ing the heater’s on/off switch located on the front of the unit.
WALL-SENS
TM
SAFETY FEATURE
In addition to the overheat safety cut-off , the Envi Heater is now equipped with an additional layer of safety to give you greater
peace of mind. Wall-Sens
TM
technology means that in the event that the Envi heater is ever removed from the wall, power will
be immediately cut to the heater. This of course means that the heater will not work if it is simply removed from its packaging
and plugged into a wall outlet. It must be mounted properly (safely) and then plugged in (or hardwired) in order for it to be
begin to heat.
GROUNDING
Plug-in models of the envi heater are for use on standard electrical circuits (eg. 120v for USA/Canada). The cord has a three-
blade grounding plug. An adapter can be obtained at most hardware or electrical stores for connecting three-blade grounding
type plugs to two-slot receptacles. The grounding lug extending from the adapter must be connected to a permanent ground
such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG.
OPERATING INSTRUCTIONS
1. Install the heater on a fi rm, level wall and plug the power cord
into a grounded power outlet (or hardwire it if applicable). The
heater will only operate when it is properly attached to the
mounting clips. Be sure to mount in upright position with the
thermostat knob on the top of the heater.
2. Once the heater is connected, press the front on/off power
switch and the POWER INDICATION LIGHT will glow red. (Fig. 5)
3. The Envi Heater is equipped with a built-in thermostat which is
adjusted with a dial at the top of the heater. Adjust the room
temperature by turning the THERMOSTAT DIAL clockwise to
increase the room temperature. If the area becomes too warm,
rotate the THERMOSTAT DIAL counter-clockwise until you reach a point where the temperature is more comfortable. (Fig. 5)
4. Once you have chosen the desired setting, the thermostat will maintain a constant temperature. NOTE: Models with no
thermostat have no temperature control and will stay on until the heater is powered off .
5. The heater is equipped with an innovative auto dimming feature that dims the power indication light for light sleeper in
darkened bedrooms. The heater automatically
detects when the light level in a room drops and then dims the power light.
6. The plug-in cordset of the Envi heater can be stored inside the bottom access door. Determine how much cordset you
require to extend out of the heater. Remove the heater from the wall, and remove the bottom access door. Carefully push
the excess cordset inside the heater and replace the bottom access door. Re-install the heater to the wall and plug-in the
cordset to continue using your heater. For more information please visit the installation web page of www.eheat.com
OPTIMAL OPERATING CONDITIONS
To get the most out of your Envi Heater, please follow these helpful hints:
1. VERY IMPORTANT!!! For optimal performance in a room, close all windows and doors and for fi rst time use, leave on
for 48 - 72 hrs.
This will allow the room to reach equilibrium temperature while the heat is gradually building up.
2. For optimal performance, mount the heater on an interior wall with the bottom of the heater 6” to 8” (15 to 20cm) from the
fl oor. For smaller rooms this can be increased with little detriment, however try to keep the bottom of the heater a maxi-
mum of 18” (46cm) from the fl oor.
3. The 475 Watt Envi heater is designed to heat rooms 130 to 150 ft
2
feet in size (12m
2
to14m
2
). This equates to a 10ft x 14ft
room size (3 x 4meters). Of course, this will vary depending on a number of factor, including outdoor temperature, room
OPERATING INSTRUCTIONS
