background image

DIN ETHERGATE (71030) 

Visit the ENTTEC website for the latest version. 

.. 

 

USER MANUAL  

10

 |

 

ID: 5928465 

Document Updated: August 2022 

 

  

 

address can be typed directly into the web browsers URL field. 

 

Unidentified IP address:

 If you are not aware of the DIN ETHERGATE’s IP address (either DHCP or Static) the 

following discovery methods can be used on a local network to discover devices:

 

 

An IP scanning software application (i.e. Angry IP Scanner) can be run on the local network to return a 

list of active devices on a local network.

 

 

Devices can be discovered using Art Poll (i.e. DMX Workshop if set to use ArtNet).

 

 

The device Default IP address 192.168.0.10 is printed on the physical label on the rear of the product.

 

 

ENTTEC EMU software (available for Windows and MacOS), which will Discover ENTTEC devices on the 

Local  Area  Network,  will  display  their  IP  addresses  and  open  to  the  Web  Interface  before  opting  to 

configure the device.

 

Note:

 The eDMX protocols, the controller and the device using to configure the DIN ETHERGATE must be on 

the same Local Area Network (LAN) and be within the same IP address range as the DIN ETHERGATE. For 

example, if your DIN ETHERGATE is on Static IP address 192.168.0.10 (Default), then your computer should be 

set to something such as 192.168.0.20. It is also recommended that all devices Subnet Mask are the same 

across your network. 

 

Home 

The landing page for the DIN ETHERGATE web interface is the Home tab. This tab is designed to give you a 

read-only device overview. This will display: 

 

System Information:

 

 

Node Name

 

 

Firmware Version

 

Current Network Settings: 

 

 

DHCP Status

 

 

IP Address

 

 

NetMask

 

 

Mac Address

 

 

Gateway Address

 

 

sACN CID

 

 

Link Speed

 

Current Port Settings:

 

 

Port 

 

 

Type 

 

 

Protocol

 

 

Universe

 

 

Send Rate

 

 

Merging

 

 

Send to Destination

 

Current DMX Buffer:

 The Current DMX buffer displays a snapshot of all current DMX values when refreshed 

manually.

 

Settings 

The DIN ETHERGATE settings can be configured within the Settings tab. Changes will only take affect after 

Summary of Contents for 71030















Reviews: