background image

EntraGuard

®

 Gold Telephone Entry Controller

1530 Old Oakland Road, Suite 100

01801-001 Rev. 2.2

San Jose, CA  95112   USA
(800) 260-5265  (408) 451-2520  FAX (408) 441-0309
Web: http://www.kerisys.com  E-mail: [email protected]

Page 15 of 32

EntraGuard

®

 – Gold

Quick S

tart Guide

5.1.3

Shared Phone Line for Multiple EntraGuard Gold Units on a Network

A single phone line may be shared for communication between multiple EntraGuard Gold units and tenants. The phone 
line is plugged into either the J3 phone plug (using an RJ11 connector) or TB-15 on the Voice Channel and Input/Output 
board of the master EntraGuard Gold unit.

On controllers using an RJ11 phone plug, the phone line then goes out of the J4 phone plug to the next unit’s J3 plug and 
so on to all the networked EntraGuard units (see Figure 16). On all other controllers, the phone line connects from TB-
15 to the next unit’s TB-15 and so on to all the networked EntraGuard units (see 

NOTE: Sharing a phone line for multiple EntraGuard units is limited to a maximum of 6 units per phone line.

Figure 16: Single Phone Line for a Multiple EntraGuard Gold Unit Network Using RJ11 Phone Plugs

Summary of Contents for Gold

































Reviews: