MN-28671
Rev 2 • 230V Enthermics Fluid Warming Cabinet Operation & Care Manual • 4
G E N E R A L I N F O R M A T I O N
C A U T I O N
THIS UNIT HAS NOT BEEN
APPROVED FOR WARMING OF
BLOOD OR BLOOD PRODUCTS.
D A N G E R
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
This warming cabinet is designed to safely warm and store either
irrigation fl uids or injection fl uids.
The single-chambered warming cabinet is constructed with 20
gauge stainless steel exterior casing and door with handle and
hinges designed to withstand heavy usage. A door with window
allows observation of inventory with the door closed. The cabinet
is warmed using low-heat-density electrothermal cable array. The
electrothermal cable is positioned in the fl oor and two sides of the
warming cabinet, providing even heating of the interior chamber.
The interior chamber temperature is regulated by an electronic
control consisting of a 4 digit L.E.D. display, ON/OFF key,
INCREASE and DECREASE keys, integrated LOCK feature and a
series of prompt sequence indicators.
The electronic control can easily be set to operate in Fahrenheit
or Celsius. After a power failure, the cabinet will remember its
programming and begin to operate as before. The ON/OFF
indicator will blink to indicate a failure occurred; pressing the
ON/OFF key once will eliminate this blinking. A thermal shut-
off system, separate from the electronic control, is included as an
additional safety feature.
The control will display temperature in whole degrees.
Fluid warming chamber
The warming cabinet can be programmed to warm either irrigation
fl uids (IRR) or injection fl uids (INJ), with separate temperature
ranges provided depending on the choice selected.
• IRR temperature range: 37° to 66°C (98° to 150°F),
• INJ temperature range: 37° to 40°C (98° to 104°F).
A fan located inside the chamber mixes the air to prevent
temperature stratifi cation and to ensure an accurate chamber
temperature for each mode.
• 0/-1.67°C (+0/-3ºF) for set points of
43° to 66°C (110° to 150°F)
• 0/-1.12°C (+0/-2ºF) for set points of
37° to 43°C (98° to 109°F).
If selected, an alarm will sound if temperatures exceed 6°C (10°F)
over the set-point temperature, and an OVERTEMP indicator will
blink indicating an over-temperature condition.
EC230L INFORMATION:
The warming cabinet is equipped with one (1) white, epoxy-
coated wire basket to accommodate fl uids packaged in bags
or bottles, mounted on basket rail supports. The basket
has a
16 liter maximum capacity.
The cabinet is furnished
with four (4) 1-1/4" (31mm) non-skid rubber feet.
EC340L INFORMATION:
The warming cabinet is equipped with two (2) white, epoxy-
coated wire baskets to accommodate fl uids packaged in bags
or bottles, mounted on basket rail supports. Each basket
has a
14 liter maximum capacity.
The cabinet is furnished
with a full perimeter rubber bumper assembly and one set of
5" (127mm) heavy duty casters, two with locking brakes.
EC390L INFORMATION:
The warming cabinet is equipped with one (1) stationary
white, epoxy-coated shelf to accommodate fl uids packaged in
bags or bottles. The basket has a capacity of
18 1-liter bottles
or 29 1-liter bags
.
The cabinet is furnished with one set of
0.5" (13mm) levelling feet.
EC770L INFORMATION:
The warming cabinet is equipped with three (3) white, epoxy-
coated wire baskets to accommodate fl uids packaged in bags
or bottles, mounted on basket rail supports. Each basket has
a
24 liter maximum capacity.
The cabinet is furnished with
a full perimeter rubber bumper assembly and one set of
5" (127mm) heavy duty casters, two with locking brakes.
(IPX-0 - Listed as Ordinary)
