manualshive.com logo in svg

entegris Optimizer ST2, Installation And Use Manual

Share
Download
entegris Optimizer ST2 Installation And Use Manual Download Page 22

OPTIMIZER ST2 FILTER MANIFOLD

21

Entegris, Inc  |  Installation and Use Manual

REPLACING THE O-RINGS

—

1.  Make sure the O-rings are not tilted or distorted.

2. If the O-ring is significantly tilted or distorted from 

the groove do not use it due to risk of chemical 
leakage.

3.  Follow the steps in this manual to remove and 

install the filter again.

4.  If re-installing the filter does not fix the O-ring 

position, follow the steps to replace the O-ring.

NOTE: For replacement O-ring ordering  
information refer to page 2. 

REMOVING THE O-RINGS

a) Grasp the far end of the connector and the  

O-ring with your thumb and forefinger.

CAUTION: Wipe away any chemical following 
safety guidelines before replacing the O-rings.

b) Pull your thumb and forefinger nearside and push 

the O-ring out. Grasp the protruding part of the 
O-ring with your other hand, and push it down 
from above to remove it from the groove.

CAUTION: Do not use any sharp tool such as 
scissors, tweezers, or knife to remove O-rings  
as it may damage the connectors or O-rings.

ATTACHING THE O-RINGS

c) Insert the O-ring into the O-ring groove on  

the connector first.

d) Then slowly push the entire O-ring along  

the groove.

e) After installation, make sure the O-ring is not 

twisted or tilted and is seated properly in the 
groove. Also ensure it is not contaminated  
with dust.

CAUTION: Make sure that O-rings are properly 
attached. Improper installation may cause 
chemical leakage.

Summary of Contents for Optimizer ST2
























Reviews:

No comments

Brands by name

Popular brands

Load more brands