background image

Encharge 3T — single-width bracket

A )  Place the wall-mount bracket on the wall so that the mounting holes 

of the bracket align with the center of the stud. 

WARNING! 

Risk of injury and equipment damage. Use the unit 

mounting holes only to mount the base unit of Encharge to the wall 

mount. Do not use the unit mounting holes to secure the bracket to 

the wall. 

B )  Use a level to keep the bottom of the wall-mount bracket level. 
C )  Use  #20(5/16”) screws (or masonry attachments for masonry) 

to attach the bracket using one screw and washer for each slot 

(9.2mm/0.36”). Use minimum of three screws in each mounting 

bracket. Tighten all screws to manufacturer’s specified torque 

values.

D )  Verify that the wall-mount bracket is solidly attached to the wall.

WARNING! 

Risk of injury and equipment damage. Do not mount 

an Encharge 3T on a bracket that is not properly mounted. 

E )  If installing additional batteries, install adjacent wall-mount brackets, 

as needed. Be sure to align the mounting holes in the wall-mount 

bracket to the center of the wall stud. You may install another row 

of brackets above the one already installed. Maintain at least 15 cm 

(six inches) vertical clearance between rows and 2.54 cm (1 inch)

horizontal clearance between units of Encharge 3T installations, and 

ensure that the wall can support the structural load (weight) of the 

installation.

WARNING! 

Risk of injury and equipment damage. Do not install 

4

Encharge 10T — triple-width bracket

A )  Place the wall-mount bracket on the wall so that the mounting holes of 

the bracket align with the center of the stud, and the mounting holes on 

the left and right align with the adjacent studs.

WARNING! 

Risk of injury and equipment damage. Use the unit mounting 

holes only to mount the base unit of Encharge to the wall mount. Do not 

use the unit mounting holes to secure the bracket to the wall. 

B )  Use a level to keep the bottom of the wall-mount bracket level. 
C )  Use #20(5/16”) screws (or masonry attachments for masonry) to attach 

the bracket using one screw and washer for each slot (9.2mm/0.36”). 

Use with a minimum of nine screws in each mounting bracket to 

support the three Encharge battery units. There is an array of slots so 

that you can choose those that allow you to mount the bracket on studs. 

Tighten all screws to manufacturer’s specified torque values.

D )  Verify that the wall-mount bracket is solidly attached to the wall.

WARNING! 

Risk of injury and equipment damage. Do not mount 

Encharge 10T batteries on a bracket that is not properly mounted. 

E )  If installing additional batteries, install adjacent wall-mount brackets, as 

needed. Be sure to align the mounting holes in the wall-mount bracket 

to the center of the wall stud. You may install another row of brackets 

above the one already installed. Maintain at least 91 cm (thirty-six 

inches) vertical clearance between rows and 91 cm (thirty-six inches) 

horizontal clearance between units of Encharge 10T installations or 

between Encharge 10T and Encharge 3/10/3T installations, and ensure 

that the wall can support the structural load (weight) of the installation.

WARNING! 

Risk of injury and equipment damage. Do not install 

more than one Encharge 10T unit per 20A branch circuit. 

Allowable tilt from vertical for Encharge installation:

Single-width mounting bracket

Front view

Angle view

Wall mount 

slots

Unit 

mount 

 

key 

holes

Wall 

mount 

slots

Unit 

mount 

 

key holes

Triple-width mounting bracket

Vertical

+5° inclination

-5° inclination

430 mm

77

5 m

m

188mm

43 mm

1270 mm

478 mm

9.2mm

478 mm

43 mm

418 mm

9.2 mm

* If the difference in flatness is more than 2mm, recommend installing a substructure like 

unistrut for better alignment of the units.

Mounting Surface 

Flatness (Across 

the Installation 

width and height) 

recommended to 

be within 2mm*

Encharge 10T 

MOUNTING SURFACE

Encharge 3T

MOUNTING SURFACE

Mounting Surface Flatness (Across 

the Installation width and height) 

recommended to be within 2mm*

      Install the Encharge 3T (single width) or Encharge 10T (tri-

ple width) wall mount bracket

Follow the instruction below for the bracket style (single-width or triple-width) 

you are installing.

WARNING! 

Risk of injury and equipment damage. Attach the wall 

mount to the wall so that it is no more than five percent from vertical. See 

the following image for reference:

Summary of Contents for ENCHARGE-10T-1P-NA










Reviews: