enorossi 16 Series User And Maintenance Manual Download Page 17 | Manualshive

Page: 17 / 72

enorossi 16 Series User And Maintenance Manual Download Page 17

17

E3

Lubrication

To top up the greasers, remove their protection caps (if
present),  remove  all  traces  of  dust  and  then  use  the
pump  to  inject  the  grease.  Afterwards,  use  a  cloth  to
remove  any  excess  grease  on  the  greasers.  Use  a
brush  to  apply  grease  wherever  there  aren’t  any
greasers.

All  grease  top-up  points  on  the  rake  are  indicated  by
labels like the one shown in the illustration.

IMPORTANT

To  avoid  pollution,  it  is  strictly  forbidden  to  dispose  of
oil,  lubricants,  filter  cartridges  or  other  noxious
materials  in  the  environment.  Comply  with  all
regulations in force on disposal of liquid and solid substances.

E4

Troubleshooting

The jack activation
command does not
respond

Hydraulic oil level
low

Hydraulic

system

piping is damaged

Hydraulic pump is
damaged

Filter is clogged

Top up oil level

Replace piping

Replace pump

Replace filter

The jacks only move
intermittently

Air in the hydraulic
circuit

Operate  the  pump  at
no  load  for  a  few
minutes,  using  the
jacks, to expel any air
in

the

hydraulic

circuit.

The jacks move even
when the command
isn’t given

Jack seals are worn
out

Replace seals

Overheated oil

Filter is clogged

Pipes are crushed

Oil level low

Replace filter

Check and replace
pipes

Top up oil level

Oil loss

Slow connection

Worn out seal

Squeeze the pipe

Replace the seal

Note: contact the Manufacturer about any faults or trouble not mentioned
in the table.

E5

Machine demolition: disposal of materials

When the rake is placed out of service, you must make harmless all parts
that could pose a safety risk to persons, animals and the environment
when sent for disposal. Materials that make up the rake and should be set
aside for segregated disposal are:

-

Iron

-

Hydraulic oil

-

Rubber

-

Plastics

These materials must be disposed of in compliance with relative national
legislation in force.

PUNTI DA

INGRASSATORI

LUBRIFICARE

«
...
15
16
17
18
19
...
»

Summary of Contents for 16 Series









































































Reviews:

No comments