manualshive.com logo in svg

Enodis TEMPSTAR, Technical Manual

Share
Download
Enodis TEMPSTAR Technical Manual Download Page 37

AFTER MAINTENANCE ACTIONS

Once the new thermostat is installed, it will be nece-

sary to ensure that it operates at the required and appropriate
ranges. The new thermostat has an adjustment that can be
turned using a small flathead screwdriver. Several cycles will
need to be run on the unit while observing the final rinse tem-
perature. The thermostat needs to cycle so that the final rinse
water meets the indicated minimums on the machine data
plate for every cycle.

SPECIAL NOTES

Work performed on Jackson dishmachines by unau-

thorized or unqualified personnel may void the warranty.
Before beginning this or any other maintenance evolution on
a unit under warranty, you should contact a certified Jackson
technician or Jackson Technical Service. You can find a list of
qualified service agencies in the back of you unit’s installation
manual.

SPECIAL PARTS

Thermostat Replacement Kit: 06401-003-13-94*

*The kit contains a thermostat, imperial brass fitting,

jumper wires and instructions.

Tempstar LT/NB/S/SDS Technical Manual 7610-011-86-35 

Issued: 06-26-2006  Revised: N/A

SECTION 5: SERVICE PROCEDURES

RINSE REGULATINGTHERMOSTAT REPLACEMENT INSTRUCTIONS (CONTINUED)

31

Calibrating the new thermostat.

Summary of Contents for TEMPSTAR




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands