background image

 

               

         

 

Repeater-EnO868SELV

 

EnOcean Repeater 868 MHz 

Repeater-EnO868USB

 

Read the operating instructions carefully before commissioning.

 

Installation and operating instructions

 

Rev.: February 2016 

Repeater-EnO868_104126_OperationManual_E_FEB2016.doc/pdf 

Page 1 of  7 

BootUp GmbH 

|

 Sonnenbergstrasse 23 

|

 CH-5236 Remigen 

|

 Switzerland 

|

 Phone +41 56 284 09 21 

|

 Fax +41 56 284 09 22 

 2016  

|

  Omi technical changes excepted 

|

   

www.BootUp.ch

   

|

   

www.myHomeControl.ch

 

|

[email protected]

 

Installation and operating instructions 

Model / Typ 

Description 

Part No. 

Repeater-EnO868USB 

EnOcean Repeater (radio amplifier) 868 MHz , Power supply via USB 
port, with USB power supply unit (EC), black 

104126 

Universal repeater (radio amplifier) for all EnOcean products 

• 

EnOcean TCM 300 (Dolphin Inside) future-proof and backward-compatible 

• 

Optimized RF antenna design combined with the surface-mounted location,  
for exceptionally good radio range. 

• 

Attractive designer plastic housing for surface mounting (Wall or ceiling)  
made of ABS flame retardant. 

• 

Power supply via USB interface, with USB type A plug and approx. 
1.2 m cable or with SELV with 6V DC, via cable 1.2 / 2.2m with open ends.  

• 

Repeater function selectable by hardware switch (no repeater, only post-master or level 1 or level 1 + 2). 

• 

Future-proof, because of "Dolphin Inside". Supported services: The old and new EEPs, Post-Master for up 
to 10 Ids, Smart-ACK and Remote Management (locate). 

Application 

Universal  repeater  (radio  amplifier)  for  EnOcean  radio  technology.  The  radio  transmission  takes  place  on  the 
European harmonized frequency of 868.3 MHz. With this device, the range between EnOcean transmitters and 
receivers can be increased. The radio signal can be cascaded to the receiver via a maximum of two repeaters. 
A  configuration  or  teach-in  is  not  required.  Also  as  a  replacement  for  radio  range  problems  in  existing 
installations.  This  device  is  identical  and  replaces  the  predecessor  RepeaterEnO868USB  Article-No.  104107 
and RepeaterEnO868SELV Article-No. 104106. 

Function 

The repeater is used for signal amplification  of the radio telegrams between  EnOcean sensors and receivers. 
This function is used when the sensor placement is outside of the receiving range of the receiver or there are 
range problems between transmitter and receiver in an existing installation. 

In  position 

Rep.  ON

  is  the  Repeater  function  active.  All  received  EnOcean  telegrams  will  be  re-sent 

automatically.  The  sent  telegrams  are  marked  as  repeater  signals.  This  tag  distinguishes  once  or  twice 
forwarded signals. 

In operating mode 

Level 1

, only original telegrams, which are telegrams originate directly from a transmitter, are 

processed and amplified again. 

In operating mode 

Level 1+2

, only original telegrams and, in addition, telegrams that have already been 

amplified once are processed and amplified again. 

If the repeater is switched off 

Rep. OFF

, then only the post master is active. 

Technical specifications 

Supply voltage: 4.75..8V DC or via USB  Power consumption: typically 70 mA @ 5V DC 

Antenna: internally 

Transmitter: EnOcean TCM 300, Step Code: DB 

Transmission power: <10mW 

Housing: ABS flame retardant, white cover, black bottom 

Transmission frequency: 868.3 MHz 

Humidity: 0 ... 75% rh, non-condensing 

Ambient temperature: 0...45°C 

Storage temperature: -25...75°C 

Protection class: IP20   IEC/EN 60529 

Dimensions: diameter 93 mm height 29 mm 

CE Marking 

Weights: 125g 

Summary of Contents for BootUp EnO868SELV








Reviews: