IMPORTANT!
READ AND FOLLOW
ALL
INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
27
ACCESSORY ITEMS
The following accessories can be added to your unit at anytime after purchase; however, let the
unit cool down before adding any accessories.
Thermostat
An
external
thermostat
(such
as
our
Part
#
PU
‐
DTSTAT
(wall)
or
Part
#
AC
‐
3003
(remote))
can
be
used
on
our
Pellet/Corn/Multi
‐
fuel
units
as
long
as
it
is
a
low
‐
voltage
that
works
with
millivolt
systems.
After
unplugging
the
unit,
locate
the
“jumper”
wire
(J
‐
18)
on
the
bottom
of
the
control
board.
The
two
screws
should
then
be
loosened
and
the
jumper
wire
removed
from
the
board.
Next,
the
two
thermostat
lead
wires
should
be
slipped
into
these
openings
and
the
screws
tightened;
the
jumper
wire
should
be
saved
for
future
operation
without
a
thermostat.
THERMOSTAT
OPERATION:
This
stove
is
equipped
with
a
unique,
new
feature
that
allows
two
options
for
thermostatic
operation:
The
stove
comes
from
the
factory
pre
‐
programmed
in
“On/Off
mode,”
which
turns
the
stove
on
and
off
when
the
call
for
heat
comes
or
leaves,
like
a
furnace.
The
second,
or
“High/Low
mode,”
burns
at
whichever
heat
range
you
set
the
stove
at
until
the
call
for
heat
leaves,
at
which
point
the
stove
goes
to
the
Low
heat
range
setting.
To
set
the
stove
in
the
“High/Low
mode,”
unplug
the
unit
and
plug
it
back
in,
then
press
and
release
both
down
arrows;
H
L
appears
in
the
heat
range
and
blower
speed
windows.
The
unit
is
now
in
“High/Low
mode.”
(Note:
Repeat
this
to
change
back
to
“On/Off
mode;”
a
0
0
will
appear
in
the
heat
range
and
blower
speed
windows).
Using
a
thermostat
in
On/Off
mode
may
shorten
the
life
of
your
stove’s
igniter.
Please
note:
Certain
units
may
not
respond
to
this;
if
your
unit
does
not
respond
in
this
manner
please
contact
Technical
Support
at
(800)
245
‐
6489.
AC-109, AC-109BN Lip Trim
There is one piece of J-Channel trim that snaps onto the ash apron. Remove the protective
covering from the trim and force the piece onto the edge. Although it should stay in place, stove
cement can be used to secure it if necessary.
ACCESSORIES AND OPTIONS
PART NUMBER
PU-OAK
AC-33000
AC-33100
PU-DTSTAT
AC-3003
AC-109
AC-109BN
AC-MBSP
PART DESCRIPTION
Outside Air Kit (Now included with unit!)
3” Corn Vent Kit (Through-the-Wall)
4” Corn Vent Kit (Through-the-Wall)
Wall Thermostat
Remote Thermostat
Brass Lip Trim
Brushed Nickel Lip Trim
High Temp. Spray Paint
Replacement Parts, Accessories and Options can be ordered from the factory at:
(Parts orders ONLY) --
(800) 516-3636
, or on our web site:
www.heatredefined.com
.
If you have any questions or problems contact the Technical Support Department:
Technical Support Department
P.O. Box 206 Parts Orders ONLY: 800-516-3636
Monroe, VA 24574 Questions: 800-245-6489 (Fax: 434-929-4810)
