Engl RACKHEAD 1060 Manual Download Page 18 | Manualshive

Page: 18 / 25

background image

A cabinet connected to the center SPEAKON® port must be rated for 8 ohms impedance and able to handle
at least 1000 watts!

Figure 4:

Mono-Block (bridged stereo power amp) with one speaker cabinet

A 4-ohm cabinet connected to the center SPEAKON® port, when operated at high volume levels, may
overload, shut down or even destroy the power amp. This is something you really want to avoid.

Page 18 / 25

«
...
16
17
18
19
20
...
»

Summary of Contents for RACKHEAD 1060


























Reviews:

No comments

Related manuals for RACKHEAD 1060

Brand: Kawai Pages: 5

Brand: James Loudspeaker Pages: 12

Brand: Zahl Pages: 20

PowerLight Series

Brand: QSC Pages: 100

Brand: Arcam Pages: 15

Brand: Prolude Amplification Pages: 15

CP-Series Power Amps CP1800

Brand: Electro-Voice Pages: 36

Sonic Frontiers Power 1

Brand: Sonic Frontiers Pages: 17

Brand: Calearo Pages: 23

Brand: Omron Pages: 103

Brand: Audio Reveal Pages: 14

Brand: Harman Kardon Pages: 50

Brand: NAIM Pages: 12

Brand: Hogtunes Pages: 12

Brand: K-array Pages: 24

Brand: Jabra Pages: 4

Brand: SUPRO Pages: 8

Brand: PRESONUS Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands