ENGINDOT GSH01B User Manual Download Page 5

Water Supply

(Cold Water Only)

Gun kicks back – Hold with both hands

The  trigger  gun  safety  lock  prevents 

the  trigger  from  accidentally  being 

engaged. This safety feature must be 

engaged  when  replacing  nozzles  or 

not in use.

The engine exhaust from this product 

contains chemicals known to the State 

of  California  to  cause  cancer,  birth 

defects  or  other  reproductive  harm. 

Operation  of  this  equipment  may 

create  sparks  that  can  start  fires 

around dry vegetation. A spark arrestor 

may  be  required.  Operator  should 

contact local fire agencies for laws or 

regulations.

Risk of asphyxiation – Use this product 

only in a well ventilated area. Do not 

operate  indoors  or  in  any  confined 

area.

Operate  and  fuel  machine  in  a  well 

ventilated area, free of devices featur-

ing  an  open  pilot  or  flame  such  as 

boilers, water heaters, etc.

Risk of fire/explosion – Do not add fuel 

when the machine is operating or still 

hot.

Risk  of  fire/explosion  -Operate  only 

where open flame or torch is permitted. 

Do not spray flammable liquids.

Do  not  operate  if  fuel  has  been 

spilled. Instead, move machine to

different location and avoid creat-

ing sparks.

This  machine  has  hot  surfaces 

which  can  cause  burns.  Operate 

in  a  safe  environment  and  away 

from children.

Do not touch hot surfaces or allow 

accessories to contact hot surfac-

es.

Do  not  leave  machine  running 

unattended.

Avoid tipping machine on its side.

When connecting to water supply 

mains,  local  regulations  of  your 

municipal water company must be 

observed. In some areas connect-

ing directly to public drinking water 

supply  may  require  a  back  flow 

prevention  device.  This  is  to 

ensure  that  there  is  no  feedback 

of chemicals into the water supply. 

Use a water filter to avoid potential 

damage  from  dirt  in  the  water 

supply.

Garden hose must be at least 5/8 

inch diameter.

Flow rate of water supply must not 

fall  below  2.6  GPM(gallons  per 

minute)

Flow  rate  can  be  determined  by 

running the water for one minute 

into an empty 5-gallon container.

The  water  supply  temperature 

must not exceed 122°F/50°C.

Never use the pressure washer to 

4

 

Summary of Contents for GSH01B




















Reviews: