background image

172 905 95  14-01

Declaration of conformity

Gas burner 
Zertifi kat TÜV Süddeutschland 

Certifi cate No

Burner

Certifi cate No

Burner

CE-0085 BT 0064

BFG1

CE-0085 BP 0352

BG550

CE-0085 AO 0230

BG100

CE-0085 BP 0353

BG550LN

CE-0085 AP 0623

BG150

CE-0085 AO 0084

BG600LN

CE-0085 AP 0624

BG200

CE-0085 BP 0354

BG650

CE-0085 AT 0192

STG120, STG146

CE-0085 AT 0313

BG700

CE-0085 AP 0625

BG300

CE-0085 AT 0314

BG800

CE-0085 AP 0626

BG400

CE-0085 BR 5754

BG950

CE-0085 AU 0156

BG450

Document:

EN 676
DIN EN 60335-2-102

EU Directive

90 / 396 / EEC

Gas Directive

2004 / 108 / EC

EMC Directive

2006 / 95 / EC

Low voltage Directive

By conforming to the above-mentioned standards and 
directives, the burner will receive the CE marking.

Genom att brännaren uppfyller ovannämnda standarder och 
direktiv erhåller brännaren CE - märkningen.

Durch Übereinstimmung mit den oben genannten Normen und 
Richtlinien erhalt der Brenner die CE-Kennzeichnung.

De par sa conformité aux normes et directives mentionnées ci-
dessus, le brûleur recevra le marquage CE de conformité.

Ljungby, Sweden, 141127 (27/11/14)

ENERTECH AB Bentone Division

  

Box 309 
SE-341 26 Ljungby Sweden

Håkan Lennartsson

Enertech AB declares that the above-mentioned products 
comply with the following standards or other normative 
documents and meet applicable sections of the EU directive.

Enertech AB försäkrar under eget ansvar att ovannämnda 
produkter är i överensstämmelse med följande standarder eller 
andra regelgivande dokument och uppfyller tillämpliga delar i EU 
direktiv.

Enertech AB erklärt hiemit, dass oben genannten Produkte mit 
den folgenden Normen oder anderen normativen Dokumenten 
übereinstimmen und die anwendbaren Teile der EU-Richtlinie 
erfüllen.

Enertech AB déclare que les produits ci-dessus mentionnés sont 
conformes aux normes ou autres documents normatifs suivants, 
et répondent aux sections applicables de la directive EU.

Enertech AB Bentone Division is quality certified according 
to SS-EN ISO 9001

Enertech AB Bentone Division är kvalitetscertifierat enligt 
SS-EN ISO 9001

Enertech AB Bentone Division ist nach SS-EN ISO 
9001qualitätszertifiziert.

Enertech AB Bentone Division a reçu la certification 
d’assurance qualité SS-EN ISO 9001qualitätszertifiziert.

Summary of Contents for Bentone BG 450





























Reviews: