background image

MODEL 13800 User Guide 

 

ANTENNA 

The wireless RF equipment described in this document is supplied 

with one of the following two (2) antenna configurations.   

 

Helical element

 Monopole Antenna: 

Antenna P/N ANT-916-CW-RH 

 

Dipole Antenna with cable: 

Antenna P/N ANT-916-MHW-RPS

 

Cable P/N PE36559-960 

 

Warning:  

This device has been designed to operate with the antennas listed 

above and having a maximum gain of 2.15 dB.  Antennas not 

included in this list or having a gain greater than 2.15 dB are 

strictly prohibited for use with this device. The required antenna 

impedance is 50 ohms. 

To reduce potential radio interference to other users, the antenna 

type and its gain should be so chosen that the equivalent 

isotropically radiated power (e.i.r.p.) is not more than that 

permitted for successful communication.  

FCC ID: TGD13800 / IC: 6120A-13800

 

This device complies with Part 15 of the FCC Rules.  Operation is 

subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause 

undesired operation.   

Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to 

operate the equipment. 

 

Summary of Contents for 13800











Reviews: