background image

MODEL 13800 User Guide 

 

ENERNET CORPORATION IS NOT RESPONSIBLE FOR ANY 
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED 
MODIFICATIONS TO THIS EQUIPMENT.  SUCH 
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO 
OPERATE THE EQUIPMENT. 
 
THIS EQUIPMENT COMPLIES WITH PART 15 OF THE FCC 
RULES.  OPERATION IS SUBJECT TO THE FOLLOWING TWO 
CONDITIONS:  (1) THIS DEVICE MAY NOT CAUSE HARMFUL 
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY 
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE 
THAT MAY CAUSE UNDESIRED OPERATION. 
 
ENERNET CORPORATION PROVIDES THIS PUBLICATION “AS 
IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS 
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE. 
 

THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES 
AND/OR TYPOGRAPHICAL ERRORS.  CHANGES ARE 
PERIODICALLY MADE TO THIS MANUAL, WHICH ARE 
INCORPORATED IN LATER EDITIONS.   
 
ENERNET CORPORATION MAY MAKE CHANGES AND 
IMPROVEMENTS TO THE PRODUCT(S) AND/OR PROGRAMS 
DESCRIBED IN THIS PUBLICATION AT ANY TIME WITHOUT 
NOTICE.  
 
IN NO EVENT WILL ENERNET CORPORATION BE LIABLE FOR 
DAMAGES, INCLUDING LOST PROFITS, LOST SAVINGS OR 
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES 
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH 
PRODUCT, EVEN IF ENERNET CORPORATION OR AN 
APPROVED RESELLER HAS BEEN ADVISED OF THE 
POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY 
ANY OTHER PARTY. 

 

E

N E R N E T

 

C o r p o r a t i o n

 

307 Dewittshire Road, Syracuse, New York 13214 

Phone:  (315) 449-0839   Fax:  (315) 449-3056

 

 
 

Summary of Contents for 13800











Reviews: