background image

 

Ascent Oil 

– August 2019 

 

HOMEOWNER/USER:  READ AND SAVE THIS INSTRUCTION MANUAL AND ACCESSORY INSTRUCTIONS FOR 

FUTURE REFERENCE. 

 
PLEASE READ THIS FIRST

 

Special Attention Flags 

Please pay particular attention to the following flags when you see them throughout this manual. 
 

DANGER:

 

Notifies you of hazards that 

WILL

 cause severe personal injury, death or substantial property damage. 

WARNING:

 

Notifies you of hazards that 

CAN

 cause severe personal injury, death or substantial property damage. 

CAUTION: 

Notifies you of hazards that 

WILL or CAN

 cause minor personal injury or property damage. 

NOTICE:

 

Notifies you of special instructions on installation, operation, or maintenance that are important, but not 
normally related to injury or property damage hazards. 

Best Practice:   Suggestions of best practices developed over many years of experience by professionals.   

 

WARNING:

 

Installation and service must be performed by a qualified installer, service agency or the oil supplier. 

 

Retain  this  manual  for  use  by  your  qualified  service  technician  only.    Should  you  observe  unusual  or 
abnormal  operation  of  the  burner  or  boiler,  contact  your  qualified  service  technician  immediately.    Do  not 
attempt to service or repair this product yourself. 

 

WARNING:

 

If the information in this manual is not followed exactly, a fire or explosion may result, causing property 
damage, personal injury or loss of life. 

 

WARNING:

 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 
or any other oil appliance. 

 

Provide unobstructed combustion air openings sized and located per boiler manual and 
applicable codes. 

 

WARNING:

 

 
 

Have  the  burner/boiler  started  up  and  serviced  at  least  once  annually  by  a  qualified  service  technician.  
Professional  care  is  necessary  to  properly  service  your  equipment  and  verify  it  is  operating  reliably.  
Failure  to  properly  maintain  the  equipment  could  result  in  severe  personal  injury,  death  or  substantial 
property damage. 

WARNING:

 

You must keep the area around the burner/boiler free from the following.  Failure to comply could result in 
severe personal injury, death or substantial property damage due to potential fire, explosion or equipment 
damage from corrosive flue products. 

 

 

Do  not  store  or  use  gasoline  or  other  flammable  vapors  or  liquids  near  or  in  the  same  room  as  the 

burner. 

 

Do  not  use  or  store  laundry  products,  paint,  varnish,  thinner  or  other  such  chemicals  near  or  in  the 

same  room  as  the  burner/boiler.    These  chemicals  cause  creation  of  acids  in  the  burner,  heat 
exchanger and vent system that can cause severe damage. 

 

Do  not  store  combustible  materials  near  or  in  the  same  room  as  the  boiler

 

or  any  other  combustion 

appliance.

 

CAUTION:  

 

DO NOT TAMPER WITH THE UNIT OR CONTROLS 

– CALL YOUR SERVICE PERSONNEL.

 

WARNING

:

 

Improper installation, adjustment, alteration, service or maintenance can cause property damage, 
personal injury (exposure to hazardous materials) or loss of life.  Refer to the user’s information manual 
provided with this boiler.  Installation and service must be performed by a qualified installer, service 
agency or the oil supplier (who must read and follow the supplied instructions before installing, servicing, 
or removing this boiler.  This boiler contains materials that have been identified as carcinogenic, or 
possibly carcinogenic, to humans). 

Summary of Contents for SYSTEM 2000 Ascent Combi





































Reviews: