Endress+Hauser Proline t-mass 65 MODBUS RS485 Manual Download Page 54

Page: 54 / 62

AMPLIFIER VERSION

Proline t-mass 65 MODBUS RS485

Hauser

AMPLIFIER VERSION

Function description, AMPLIFIER VERSION group

DEVICE SOFTWARE

Description

Use this function to display the current device software version.

MODBUS register:
Data type:
Access:

7277
String (16)
read

HARDWARE REVISION
NUMBER AMPLIFIER

Description

Use this function to view the hardware revision number of the amplifier board.

MODBUS register:
Data type:
Access:

7030
String (16)
read

SOFTWARE REVISION
NUMBER AMPLIFIER

Description

Use this function to view the software revision number of the amplifier board.

MODBUS register:
Data type:
Access:

7039
String (16)
read

SOFTWARE REVISION
NUMBER T-DAT

Description

Use this function to view the software revision number of the T-DAT.

MODBUS register:
Data type:
Access:

7048
String (16)
read

I/O MODULE TYPE

Description

Use this function to view the configuration of the I/O module.

MODBUS register:
Data type:
Access:

7285
Integer
read

SOFTWARE REVISION
NUMBER I/O MODULE

Description

Use this function to view the software revision number of the I/O module.

MODBUS register:
Data type:
Access:

7078
String (16)
read

Summary of Contents for Proline t-mass 65 MODBUS RS485































































Search results

Summary of Contents for Proline t-mass 65 MODBUS RS485

Reviews:

Related manuals for Proline t-mass 65 MODBUS RS485

Brands by name

Popular brands

Endress+Hauser Proline t-mass 65 MODBUS RS485, Manual

Search results

Summary of Contents for Proline t-mass 65 MODBUS RS485

Reviews:

Related manuals for Proline t-mass 65 MODBUS RS485

Brands by name

Popular brands