Endress+Hauser Proline Prosonic Flow 93C, Operating Instructions Manual

Page: 64 / 90

Troubleshooting Proline Prosonic Flow 93C FOUNDATION Fieldbus
64 Hauser
043 Device status message (FF):
T-DAT data inconsistent –
Err. No. 043
Local display:
S: C-DATA T-DAT
$
: # 043
BLOCK_ERR = Device needs
maintenance now OUT. QUALITY = BAD Cause:
Error in calibration data
Remedy:
1. Check whether the T-DAT is correctly plugged
into the amplifier board.
2. Replace the T-DAT if it is defective.
Check that the new, replacement DAT is
compatible with the measuring electronics.
Check the:
- Spare part set number
- Hardware revision code
3. Replace measuring electronic boards if
necessary.
Transducer_Error = Electronics
failure OUT. SUBSTATUS = Device
Failure
BLOCK_ERR = Input Failure
(faulty input value from
Transducer Blocks)
082 Device status message (FF):
Interruption between sensor
and transmitter CH1 -
Err. No. 082
Local display:
S: SENS. DOWN CH1
$
: # 082
BLOCK_ERR = Device needs
maintenance now OUT. QUALITY = BAD Cause:
Connection between sensor channel 1/2 and
transmitter interrupted.
Remedy:
1. Check the cable connection between the
sensor and the transmitter.
2. Check that the sensor connector is fully
screwed in.
3. Check that the correct sensor has been
connected.
4. Local display:
In the SENSOR TYPE function (6881), check
that the correct sensor has been selected for
Channel 1 or Channel 2.
5. FOUNDATION Fieldbus:
In the "Sensor Param. - Sensor Type"
parameter, check whether the correct sensor
has been selected for error number 82 or 83.
6. The sensor may be defective.
Transducer_Error =
Mechanical failure OUT. SUBSTATUS = Device
Failure
BLOCK_ERR = Input Failure
(faulty input value from
Transducer Blocks)
083 Device status message (FF):
Interruption between sensor
and transmitter CH2 -
Err. No. 083
Local display:
S: SENS. DOWN CH2
$
: # 083
BLOCK_ERR = Device needs
maintenance now OUT. QUALITY = BAD
Transducer_Error =
Mechanical failure OUT. SUBSTATUS = Device
Failure
BLOCK_ERR = Input Failure
(faulty input value from
Transducer Blocks)
085 Device status message (FF):
Interruption between sensor
and transmitter CH1 -
Err. No. 085
Local display:
S: SENS. UP CH1
$
: # 086
BLOCK_ERR = Device needs
maintenance now OUT. QUALITY = BAD Cause:
Connection between sensor channel 1/2 and
transmitter interrupted.
Remedy:
1. Check the cable connection between the
sensor and the transmitter.
2. Check that the sensor connector is fully
screwed in.
3. Check that the correct sensor has been
connected.
4. Check that the correct sensor has been
selected.
– FF: Transducer Block "Transducer_CH1"
(base index: 1400) or Transducer Block
"Transducer_CH2" (base index: 1500)
→
Parameter "Sensor Param. - Sensor Type"
– Onsite display: BASIC FUNCTION
→
SENSOR DATA CH1 or CH2
→
SENSOR
PARAMETERS
→
SENSOR TYPE
5. The sensor may be defective.
Transducer_Error =
Mechanical failure OUT. SUBSTATUS = Device
Failure
BLOCK_ERR = Input Failure
(faulty input value from
Transducer Blocks)
086 Device status message (FF):
Interruption between sensor
and transmitter CH2 -
Err. No. 086
Local display:
S: SENS. DOWN CH2
$
: # 086
BLOCK_ERR = Device needs
maintenance now OUT. QUALITY = BAD
Transducer_Error =
Mechanical failure OUT. SUBSTATUS = Device
Failure
BLOCK_ERR = Input Failure
(faulty input value from
Transducer Blocks)
No. Error messages:
FOUNDATION Fieldbus
(FF)*
(local display) Transducer Block
error messages
"Diagnosis" Transducer
Block Analog Input Function Block
error messages Reason for error/rectification
(spare parts
→
ä
71)