background image

Levelflex FMP55 PROFIBUS PA

About this document

Hauser

3

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.1.2  

Electrical symbols

Protective earth (PE)

Ground terminals that must be connected to ground prior to establishing any other

connections.

The ground terminals are located on the inside and outside of the device.

• Inner ground terminal; protective earth is connected to the mains supply.

• Outer ground terminal; device is connected to the plant grounding system.

2.1.3  

Tool symbols

Flat-blade screwdriver

Allen key

Torx screwdriver

Open-ended wrench

2.1.4  

Symbols for certain types of information and graphics

 Permitted

Procedures, processes or actions that are permitted

 Forbidden

Procedures, processes or actions that are forbidden

 Tip

Indicates additional information

Reference to documentation

Reference to graphic

Notice or individual step to be observed

Summary of Contents for Levelflex FMP55 PROFIBUS PA





























Reviews: