manualshive.com logo in svg

ENDEVCO 133, Instruction Manual

Share
Download
ENDEVCO 133 Instruction Manual Download Page 16

 

 

ENDEVCO

    www.endevco.com    Tel: +1 (866) ENDEVCO  [+1 (866) 363-3826] 

IM133, Page 16 

®

 

This special mode is selected by pressing the “Select Function” push button while simultaneously 
pressing the LEFT EDIT push button. The unit returns to the normal mode of operation (Monitoring 
or Non-monitoring state) after pressing the “Select Function” push buttons one more time. 

 
 

After the mode is selected, all of the “Function LEDs” will be off and the first error code will be 
shown on the LED display. The user may scroll through the list by using the UP and DOWN EDIT 
push buttons. 

 
 

3.  Reset 

 
 

This special mode selection allows the user to reset the unit (equivalent to a power-up initialization). 

 
 

This special mode is selected by pressing the “Select Function” push button while simultaneously 
pressing the UP EDIT push button. The unit returns to the normal mode of operation (Monitoring 
or Non-monitoring state) immediately after initialization. 

 
 

4.  Store Setup in EEPROM 

 
 

This special mode selection allows the user to force the unit to store all of the function settings into 
non-volatile memory. 

 
 

This special mode is selected by pressing the “Select Function” push button while simultaneously 
pressing  the  DOWN  EDIT  push  button.  The  unit  returns  to  the  normal  mode  of  operation 
(Monitoring or Non-monitoring state) immediately after writing all of the function settings into non-
volatile memory. 

 
 

5.  Test Display 

 
 

This  special  mode  selection  allows  the  user  to  test  the  display  board  by  displaying  a  different 
pattern  on  the  LED  indicators  and  the  LED  display  every  time  any  one  of  the  front  panel  push 
buttons is pressed. 

 
 

This special mode is selected by pressing the “Select Function” push button while simultaneously 
pressing the UP and LEFT EDIT push buttons. The unit returns to the normal mode of operation 
(Monitoring or Non-monitoring state) after pressing the “Select Function” push button one more 
time. 

 

 

6.  Recall Default Setup 

 
 

This special mode selection allows the user to recall the default function settings. 

 
 

This special mode is selected by pressing the “Select Function” push button while simultaneously 
pressing  the  DOWN  and  RIGHT  EDIT  push  buttons.  The  unit  returns  to  the  normal  mode  of 
operation (Monitoring or Non-monitoring state) immediately after restoring all of the default function 
settings. 

 

Function 

Factory Default Setting 

1.  Input Select 

Volt (ISOTRON) 

2.  Current Exc. (mA) 

0.0 (off) 

3.  Sensitivity 

1.000 

4.  Output Scaling 

1.000 

5.  HP Filter 

10.0 (on) 

6.  LP Filter 

XX.XX (on) 

7.  Monitoring State 

V out 

Summary of Contents for 133






























Reviews:

No comments

Brands by name

Popular brands

Load more brands