background image

6

  

Only use the MANUAL ACTIVATION / RESET button when a problem has been detected, and

     after you have resolved the issue causing the problem.

■  

Pressing the MANUAL ACTIVATION / RESET button will cause the REVERSE POLARITY

     protection to be DISABLED until such time as the SMART CABLE is physically disconnected / 

     reconnected to the jump start unit.

■  

In such situation, be very careful NOT to reverse the polarity when this button has been pressed.  

    Otherwise you may cause damage to the cable and the jump start unit.

MOBILE PHONE / TABLET / PC CHARGING

A series of charging adaptors are supplied with this unit.  However, we recommend using the charging 

cable supplied with your original product.  For phones / tablets, plug the USB port of the charging cable 

into the USB 5V output port, and the adaptor to your device.  
The 12V DC connection can be used for charging 12V devices. The maximum output current is 15A.

RECHARGING THIS UNIT

Press the POWER switch to start charging. This unit should be charged using the a 240V AC (15V / 1A) 

adaptor supplied. 
Using the 240V AC adaptor, it will take approximately 5 hours to fully charge the unit.  

To extend the battery life, it is recommended to fully charge the unit every 3 - 6 months.

LED LIGHTS

Further pressing the power switch will cycle between SOS mode, flashing mode, and then off.  Depress the 

POWER switch for 3 seconds to directly turn off the LED light.

SPECIFICATIONS

Capacity                                                     16,800mAh
Peak current                                             1200CCA
Charging                                                    DC15V/1A (5 hrs)
USB output                                                U USB5V2.1A
DC output                                                 12V - 16V/15A          
Working temperature                            -20

o

C to 60

o

C

Storage temperature                             -20

o

C to 60

o

C

Summary of Contents for ET6795









Reviews: