EMT 928 II User Manual Download Page 10

Page: 10 / 13

Manual-EMT-928

10/13

Operation

The EMT 928 features the following elements for operation:

Switch for setting the function

Switch for setting the speed

LED, showing function and battery level

Speed
Set the switch (2) to the desired speed position. For further information
about speed adjustment, please refer to the next page.

Operation

Switch (1)

Function

Battery

LED

Info

Battery level

Platter Stop

Charging

(if charger is switched on)

Green, steady glowing

Pure listening mode

Green, blinking slowly

Maintenance charging

Fully charged

Platter Run

Pure listening mode

Connected to drive only

Green, blinking fast

Charger switched off

Red, glowing steady

Pure listening mode

RESERVE

Platter Run

Charging

(if charger is switched on)

Red, blinking slowly

Charging

Red, blinking fast

Charger switched off

RESERVE

Summary of Contents for 928 II














Search results

Summary of Contents for 928 II

Reviews:

Related manuals for 928 II

Brands by name

Popular brands

EMT 928 II, User Manual

Search results

Summary of Contents for 928 II

Reviews:

Related manuals for 928 II

Brands by name

Popular brands