background image

 

TSD012                                                                                                 SIGNALPOINT I/O UNIT, ISSUE 1 – 09/09/13 

 

10

 

Press the ‘YES’ key to change and the screen will now display:  

 

 

11

 

Press the ‘0’ key and the screen will now display: 

 

 

12

 

Enter the slot number that you want to add a device to 

(e.g. 125) then press the ‘YES’ key and the Screen will 

now display:   

 

 

13

 

Press the ‘

 key until the screen displays: 

 

   

 

 

14

 

Press the ‘YES’ key and the screen will now display: 

 

 

 

15

 

Take the device you want to log on.  

Press and hold the logon button for 2-3 seconds 

(Shown On Figure 1) and the screen will now display:  

 

 

 

 

 

 

 

  Enter Device 
   (Numbers 1-256) 
   Number> 
  Yes= Finish

 

 

   Time  

|**Logon Options**     | 
 >Logon Slot :125         < 
|Slot is          :FREE       | 
 Yes= Select

 

 

   Time  

| Slot is         :FREE       | 
 >Logon is DISABLED< 
 
|\/\/\/\/\/\/\/\/\/\/\/|

 

|  Slot is        :FREE       | 
 > Logon is  ENABLED< 
 | /\/\/\/\/\/\/\/\/\/\ | 

     

 Logon Default Device 
 125 
     
  Yes= Select

 

 

  Time 

 Added Default Device 
 125 
     
  Yes= Select

 

 

  Time 

Summary of Contents for Signal point









Reviews: