Empire DVC55IPXLP-1, Installation Instructions And Owner'S Manual

Page: 15 / 44

37403-5-0620 Page 15
IF ANY OF THE ORIGINAL WIRE AS SUPPLIED
WITH THIS UNIT MUST BE REPLACED, IT MUST
BE REPLACED WITH 150°C THERMOPLASTIC
4/64 THICK OR ITS EQUIVALENT.
120V. 60Hz. LESS THAN 3 AMPS
S´IL Y A UN FIL ORIGINAL FOURNI AVEC
L´APPAREIL QUI DIOT ÊTRE REMPLACÉ. IL DOIT
ÊTRE REMPLACÉ AVEC UN FIL
THERMOPLASTIQUE 150°C.
120V. 60Hz. MOINS DE 3 AMPS.
—————— ———————————————————— ———————————————————————————
WHITE (BLANC)
LOW VOLTAGE (BAS VOLTAGE)
120 VOLTS
120 VOLTS
SCHEMATIC WIRING DIAGRAM
——————————————————————————————
SCHÉMA É INSTALLATION LECTRIQUE
JUNCTION BOX
—— —— ——— ———— —————————— — —
BOÎTE DE JONCTION
LIMIT CONTROL
——— — ———— ——————————— —
CONTROL DE
TOLERANCE
AUTO FAN
——— —— ———— ——————— —
VENTILATE
AUTO
TRANSFORMER
——— —— ———— —————————————— —
TRANSFORMATEUR
SPT-3 CORDSET
——— —— ———— ——————————— —
CORDON SPT-3
BLACK (NOIR)
LADDER WIRING DIAGRAM
——————————————————————————
DIAGRAMME À L´ÉCHELLE
D´INSTALLATION ÉLECTRIQUE
YELLOW
——— — ————————
JAUNE
WHITE
——— — ————————
BLANC
BLACK
——— — ————————
NOIR
RED
—
ROUGE
WHT
—
BLANC
TRANSFORMER
——— —— ———— —————————————— —
TRANSFORMATEUR
24 VOLTS
MOTOR
————— ———— —
MOTEUR
AUTO FAN
——— —— ———— ——————— —
VENTILATEUR
AUTO
MOTOR
————— ———— —
MOTEUR
BRN/Brun
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV
GRND
GAS VALVE
——— — ———— ——————————— —
VALVE DE GAZ
MODULE
LIMIT CONTROL
——— — ———— ——————————— —
CONTROL DE
TOLERANCE
GAS VALVE
——— — ———— ——————————— —
VALVE DE GAZ
BRN/Brun
MODULE
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV MV
MV/PV
PV
GRND
24V
24V
R12352
ON/OFF DEVICE
——— — ———— ——————————— —
ON/OFF
PÉRIPHÉRIQUES
WIRE
NUT
— — ———— ——————— —
FILS
TORSADÉS
WIRE NUT
— — ———— ———————---------------- —
FILS TORSADÉS
ON/OFF DEVICE
——— — ———— ——————————— —
ON/OFF
PÉRIPHÉRIQUES
Wiring
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1 , if an external electrical source is utilized. This appliance
is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged directly into
a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded
receptacle, an adapter, which has two prongs and a wire for grounding, can be purchased, plugged into the ungrounded receptacle and
its wire connected to the receptacle mounting screw. With this wire completing the ground, the appliance cord plug can be plugged into
the adapter and be electrically grounded. A 7/8" hole is provided in the junction box for use with a conduit connector if local codes require
this type of protection.
Installing the ON/OFF Device
To install an ON/OFF device (such as a wall switch, remote, toggle switch,or thermostat), remove the wire nut from the two wires from
the valve. Run additional wire from the valve wires to the ON/OFF device. Install the ON/OFF device in the same room as the furnace
following the installation instructions supplied with it. In the absence of instructions, install the ON/OFF device 4 to 5 feet above the floor
on an interior wall not affected by another heating source (i.e. stove or water heater) or the temperature of an adjoining room.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
To Conserve Gas: Turn off pilot when heater is not in use.
Figure 13
WIRING