background image

27451-1-0810

Page 6

any vent-free gas Log Heater must be “For use with approved 

anSi Z21.11.2 unvented room heater.”
Follow and complete the installation instructions of the gas log set 

and the requirements of this firebox.
Check all fittings for leaks before lighting the gas log set.
In  planning  the  installation  for  the  firebox,  it  is  necessary  to 

determine where the unit is to be installed and whether optional 

accessories are desired. gas supply piping should also be planned 

at this time.

A gas shut off must be in this line.

The firebox can be mounted on any of these surfaces:

1.  A flat hard combustible or non-combustible surface.

2.  a  raised  platform  of  combustible  or  non-combustible 

material.

3.  Recessed into the floor as illustrated by

 figure 4

.

4.  Supported under all (4) corners of the firebox so that contact 

is made on all four perimeter edges on the bottom of the unit 

(example: Four (4) concrete masonry blocks).

if  the  firebox  is  installed  directly  on  carpeting,  tile  or  other 

combustible material other than wood flooring, it should be installed 

on a metal or wood panel extending the full width and depth of 

the unit.
at this point, you should have decided what components to include 

in your installation, and where the firebox is to be located. If this 

has not been done, stop and consult your dealer for assistance with 

this planning.

planning your Installation

accessory kits such as the FBB5 Blower kit, trim kits, Mantles, 

plus other Decorative Frame, Hood, and Door accessory kits may 

be installed after the firebox is secured to the framing.

Refer  to  the  instructions  provided  with  each  of  the  optional 

accessory kits for proper installation and operation.

Firebox Framing

Firebox  framing  can  be  built  before  or  after  the  firebox  is  set 

in place. Framing should be constructed to accommodate wall 

figure 4 

figure 5

FiReBoX inStaLLation inStRUctionS

FLUSH FACE

LOUVERED

COMBUSTIBLE MATERIALS ALLOWED

Premium Vent-Free Firebox Framing Dimensions (in 

inches)

"A"

"B"

"C"*

Model

Framing 

Height

Framing 

Width

Framing 

Depth

VFP36SB

41 1/2"

40"

23"*

VFP36PB

41 1/2"

39"**

23"*

Attention: 

Add height of base to "A" Dimension when elevat

-

ing firebox if installing on an elevated base.

framing dimension A incudes a three inch clearance for 

standoffs on firebox.

*Dimension "C" assumes use of 1/2" wall board flush to both 

front faces.

** Peninsula model framing width assumes use of 1/2" wall 

board flush to the end face.

A

B

C

A

B

C

framing - peninsula

framing - See-Through

covering and firebox facing material. The firebox framing should 

be constructed of 2 x 4 lumber or heavier. the framing headers 

may rest on the top of the firebox standoffs. Refer to 

figure 5 

for 

firebox framing dimensions.

Note:

 on Peninsula models, a maximum weight of 250 lbs. is 

recommended when construction materials are supported by the 

top standoff spacers.

Summary of Contents for VFP36PB2EF-3





















Reviews: