background image

Homeowner’s Installation and 

Operating Manual

DESIGN

CERTIFIED

10003848  1/07  Rev. 3

WARNING! 

IF THE INFORMATION IN THIS 
MANUAL IS NOT FOLLOWED 
EXACTLY, A FIRE OR EXPLOSION 
MAY RESULT, CAUSING 
PROPERTY DAMAGE, PERSONAL 
INJURY OR LOSS OF LIFE.

WHAT TO DO IF YOU SMELL GAS:

• 

Do not try to light any appliance. 

• 

Do not touch any electric switch; do 
not use any phone in your building. 

• 

Immediately call your gas supplier 
from your neighbor’s phone. Follow 
the gas suppliers instructions. 

• 

If you cannot reach your gas supplier 
call the fire department.

DO NOT STORE OR USE GASOLINE OR 
OTHER FLAMMABLE VAPORS AND/OR 
LIQUIDS IN THE VICINITY OF THIS OR 
ANY OTHER APPLIANCE.

Bay Window 
Rear/Top Convertible 
Direct Vent Fireplaces 
Model: DVRTSB

 

   

INSTALLER/CONSUMER

SAFETY INFORMATION

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND USING 
APPLIANCE

FOR YOUR SAFETY

Installation and service must be 
performed by a qualified installer, 
service agency or your gas supplier.

CERTIFIED

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary of Contents for DVRTSB





































Reviews: