Empire Comfort Systems VFP30CA30 Series Installation Instructions And Owner'S Manual Download

Page: 20 / 32

26563-0-0410

Page 20

USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INjURY OR DEATH.

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

PARTS LIST

INDEX NO.

PART NO.

DESCRIPTION

15484

oUtLet BaFFLe

24043

FIREBOX BRACE (2 REQUIRED)

23938

FiReBoX toP

24034

FiReBoX WaLLs

24017

ReaR Log sUPPoRt

15567

scReen FRaMe asseMBLY

R-3624

PiLot asseMBLY - nat

R-3623

PiLot asseMBLY - LPg

24560

PiLot BRacket

26562

BURneR asseMBLY

P-253

FITTING, ORIFICE ANGLED

24429

BRACKET, ORIFICE HOLDER

R-7572

JaMB nUt

P-184

oRiFice #35 - nat

P-250

ORIFICE #1.65mm - LPG

26561

aiR sHUtteR BRacket

24041

FiReBoX BottoM

15977

VaLVe BRacket

24024

TUBING ASSEMBLY (VALVE TO BURNER)

24246

TUBING ASSEMBLY (VALVE TO PILOT) (LPG ONLY)

24562

TUBING ASSEMBLY (REGULATOR TO PILOT) (NAT ONLY)

R-7063

PILOT REGULATOR (NAT ONLY)

24561

TUBING ASSEMBLY (VALVE TO REGULATOR) (NAT ONLY)

R-2423

CONNECTOR, MALE 5/16

R-9368

VaLVe - nat

R-3625

VaLVe - LP

R-9760

PIEZO IGNITER

15516

VaLVe coVeR asseMBLY

R-9616

Log - FRont LeFt cHUnk

R-9615

Log - centeR LeFt

R-9613

Log - ReaR

R-9618

Log - LeFt tWig

R-9617

Log - RigHt tWig

R-9614

Log - FRont RigHt

24035

ReaR coVeR

26051

WiRe cHanneL - RigHt

R-3436

REMOTE/OFF/ON SWITCH

26052

WiRe cHanneL - LeFt

not sHoWn

R-9698

WiRe asseMBLY

Summary of Contents for VFP30CA30 Series

































Search results

Summary of Contents for VFP30CA30 Series

Reviews:

Related manuals for VFP30CA30 Series

Brands by name

Popular brands

Empire Comfort Systems VFP30CA30 Series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for VFP30CA30 Series

Reviews:

Related manuals for VFP30CA30 Series

Brands by name

Popular brands