background image

42929-2-0721

Page 1

Empire Comfort Systems Inc. • Belleville, IL

INSTALLATION INSTRUCTIONS

HEAT MANAGEMENT SYSTEMS KIT

WARNING

If not installed, operated and maintained 

in accordance with the manufacturer’s 

instructions, this product could expose you 

to substances in fuel or from fuel combustion 

which can cause death or serious illness.

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death or 

property damage.

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

do not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow 

the gas supplier’s instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

HMFA-1 FORCED AIR 

HEAT MANAGEMENT 

SYSTEMS KIT 

FOR USE WITH 

VENT-FREE 

FIREPLACE 

MODELS:

VFLB(36,48,60,72)FP(30,90)(N,P)

WITH HMFA(36,48,60,72)P AND HMFATV

GAS-FIRED

UL FILE NO. 

MH46389

Summary of Contents for VFLB36FP30N





























Reviews: