background image

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

POWER-VENT

HIGH-EFFICIENCY FIREPLACE

MODELS

FF28BM(N,P)-1

FI28BM(N,P)-1

FW28BM(N,P)-1

WARNING: If not installed, operated and main-

tained  in  accordance  with  the  manufacturer’s 

instructions,  this  product  could  expose  you  to  

substances in fuel or from fuel combustion which 

can cause death or serious illness.

Installer:  Leave  this  manual  with  the  

appliance.

Consumer:  Retain  this  manual  for  future  

reference.

—  Do not store or use gasoline or other flamma

-

ble vapors and liquids in the vicinity of this or 

any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately  call  your  gas  supplier  from 

a  neighbor’s  phone.  Follow  the  gas  sup-

plier’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation  and  service  must  be  performed 

by a qualified installer, service agency or the 

gas supplier.

WARNING:  If  the  information  in  these  

instructions are not followed exactly, a fire or 

explosion may result causing property damage, 

personal injury or loss of life.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only)  or  mobile  home,  where  not  prohibited  by 

state or local codes.
This appliance is only for use with the type of gas 

indicated  on  the  rating  plate.  This  appliance  is 

not convertible for use with other gases, unless a 

certified kit is used.

EMPIRE

EMPIRE

Comfort Systems

ATTENTION: THIS APPLIANCE  IS  NOT TO 

BE INSTALLED IN CANADA.

WARNING

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

Summary of Contents for Mantis FF28BMN-1

























































Reviews: