EMIT SmartLog V5 Installation, Operation And Maintenance Manual Download Page 4 | Manualshive

Page: 4 / 13

background image

TB-6584

Page 4 of 13

© 2016 DESCO INDUSTRIES, INC.

Employee Owned

Items and Accessories

The EMIT SmartLog V5™ is available in four models:

Item

Description

50766 SmartLog V5™, North America
50767 SmartLog V5™, Asia
50768 SmartLog V5™, Europe
50769 SmartLog V5™, Europe, 10mm Adapter

EMIT offers the following accessories for the SmartLog V5™:

Item

Description

50764 Reader, HID ProxPoint Plus 6005
50765 Reader, HID iClass R10
50415 Stand, SmartLog
50775 ESD Glove Test Fixture
50773 SmartLog V5™ Turnstile, 120VAC
50772 SmartLog V5™ Turnstile, 220VAC
50771 Turnstile Bracket, SmartLog V5™**
50424 Limit Comparator for Testers

Packaging - SmartLog V5™ Test System

1 SmartLog V5™

1 Mounting Bracket

1 Dual Independent Foot Plate

1 Foot Plate Cable, 6'

1 Power Adapter, 9VDC 1.25A center pos.

1 Right Angle Ground Cord

2 Mounting Anchors

2 Mounting Screws

1 Thumb Screw

1 10mm Wrist Cord Adapter (50769 only)

1 Certificate of Calibration

**See page 8 for installation instructions.

Use the SmartLog V5™ along with the TEAM5 Software to automate the collection of employee ESD testing. This software

is offered in two tiers: TEAM5 and TEAM5 Enterprise.

Item

Description

50491 TEAM5 Enterprise Software
50493 TEAM5 Software

www.

.com

[email protected]

1.800.561.8187

«
...
2
3
4
5
6
...
»

Summary of Contents for SmartLog V5














Reviews:

No comments

Related manuals for SmartLog V5

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Barreto Pages: 20

Brand: Barreto Pages: 18

Brand: Backyard Discovery Pages: 41

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: ParaBody Pages: 5

Brand: Olsen Pages: 58

Brand: Tanco Pages: 112

Brand: Omlet Pages: 60

Brand: Nakayama Pages: 14

FUSION APOLLO MS-WB675

Brand: Garmin Pages: 18

Brand: Rapid Shape Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands