background image

www.enviromaster.com

CAC Cassette Evaporator

6

CAC CASSETTE PREPARATION AND POSITIONING

POSITIONING

The Cassette installation position should be 

selected with the following points in mind:

1. Pipe work, electrical connections, con-

trol box and condensate pump access 

panels should be readily accessible.

2. The unit should be positioned at least 

5 ft. from a wall or similar obstruction. 

Position the unit as close to the center 

of the room as possible to insure air is 

distributed evenly.

3. Position the unit so that the discharge air 

does not blow directly on the thermostat.

4. The unit should not be positioned di-

rectly above any obstructions.

5. The condensate drain should have suf-

ficient fall (1” per 10’) in any horizontal 

run between Cassette and drain. Maxi-

mum condensate pump lift is 36”.

6. There should be a minimum 1” clear-

ance above the depth of the Cassette 

and the false ceiling for proper instal-

lation, shown below (see the “CAC Di-

mensions” section in the back of this 

IOM for cabinet sizing):

Small Cabinet Dimension A = 12¾” min.

Medium Cabinet Dimension A = 11½” min.

Large Cabinet Dimension A = 13½” min.

Dimension A + 1” = minimum space 

above the false ceiling for installation

A

A +1”

Figure #1

Model # 

Evaporator

Condenser 

Btuh

Factory  Installed 

Piston-Orifice Size

Field Changeover

Piston-Orifice Size

CACA24

T2CA4400

T2CA2400 

T2CA8400

.059”

.063”

CACA24

T3CA9240

T3CA2240

T3CA9940

.059”

.063”

 “4” in the capacity decoding field = 24,000 Btuh

Evaporator

Importent 

- Replace the existing 

piston  (

before 

installing  the  unit) 

with  the  piston  supplied  in  the  Kit  Bag:

when a CACA24 evaporator is matched with a 

T2CA4400, T2CA2400, T2CA8400 or T3CA9240, T3CA2240, 

T3CA9940 

condenser which has a 24,000 Btuh compressor 

(“4” in the capacity decoding field) the piston will need relacement 

only

 on the 24,000 Btuh zone. *

Your EMI evaporator unit contains the appropriate piston for your model. Refer to 

this document to determine if a change is required based on your condenser rating. If 

your match is

 

not listed

 

below

 no piston change 

is required.

 

(See chart)

PISTON/ORIFICE INSTALLATION INSTRUCTION 

Summary of Contents for CAC

































Reviews: